Search found 178 matches: chatter how do
Searched query: chatter how do
ignored: how do
- Thu Dec 21, 2023 10:55 am
- Forum: The Chiff and Fipple Whistle Forum
- Topic: Making wooden whistles - a few questions
- Replies: 26
- Views: 2522
Re: Making wooden whistles - a few questions
... made for all the sections of all the instruments I make. This is critical for turning thin walled tubes. Without them you will have problems with chatter, and thin walled wooden tubes are very easy to crack or crush if you try gripping them directly. As you get into this you'll find that it is ...
- Wed Sep 28, 2022 7:23 pm
- Forum: Flute Forum
- Topic: Lizzo and the Laurent
- Replies: 25
- Views: 5870
Re: Lizzo and the Laurent
... did a very silly SNL skit (redundant, I know!) about the flute and classical music (Beethoven, IIRC) a while ago and anecdotally I heard a lot of chatter about it, so again, lots of eyes/ears reached. I won't lie and say I'm a Lizzo superfan or anything but she is genuinely enthusiastic and seems ...
- Sun Sep 04, 2022 6:05 am
- Forum: Flute Forum
- Topic: "The McKenna Influence"
- Replies: 21
- Views: 3579
Re: "The McKenna Influence"
... for Diapason Normal as 435Hz at 59ºF (15ºC) presumably relates to church organs in France. Who else is going to be playing music while their teeth chatter?
- Mon Feb 21, 2022 8:11 am
- Forum: The Chiff and Fipple Poststructural Pub
- Topic: Tell me about Willie Clancy Week?
- Replies: 14
- Views: 12931
Re: Tell me about Willie Clancy Week?
... in the school in Spanish Point, tables are set up for selling stuff. Launches in a separate room (I usually buy what I want avoid the launching chatter there but you may want to find someone to launch the thing for you, if you are into that sort of thing). Na Piobairi Uilleann used to run a ...
- Sat Jan 22, 2022 1:34 pm
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... the smoothness of a deep hole. I don't design the reamer around the idea of deep flutes to hold chips; quite the opposite. The spiral can reduce chatter but has no value in removing chips, Many of my reamers have six flutes, but my latest have 5. With five flutes, the "tooth load" increases, ...
- Fri Jan 21, 2022 9:10 am
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... the smoothness of a deep hole. I don't design the reamer around the idea of deep flutes to hold chips; quite the opposite. The spiral can reduce chatter but has no value in removing chips, Many of my reamers have six flutes, but my latest have 5. With five flutes, the "tooth load" increases, ...
- Thu Jan 20, 2022 11:13 am
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... no change in tooling for the different woods. Do the different woods ream differently? Yes, a ... Mr. Chainwhip didn’t seem to notice or care. Chatter/vibration can be more of an issue with certain ... is speaking to you, trying to inform you. How’s that walking on rice paper coming along Grasshopper? ...
- Thu Jan 20, 2022 8:29 am
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... back up the reamer. Straight fluted reamers don't encourage the chips to move along the reamer ... college did teach me that much :wink: ) , however my thoughts and comments, questions on the ... have more of a tendency to wander and vibrate/chatter, but I simply don’t know. Then there’s the ...
- Wed Jan 19, 2022 1:38 pm
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... for me: The initial bore can be off center. For best results, I must do the initial drilling (and drying), then hold the workpiece between centers. ... with the ID*. Making the workpiece co-axial with the tool reduces chatter and the bell-ends described by Loren. Maybe this step would have ...
- Wed Jan 19, 2022 12:47 pm
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... for me: The initial bore can be off center. For best results, I must do the initial drilling (and drying), then hold the workpiece between centers. ... with the ID*. Making the workpiece co-axial with the tool reduces chatter and the bell-ends described by Loren. Maybe this step would have ...
- Wed Jan 19, 2022 10:08 am
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
Re: reaming
... than the diameter of the reamer, just as the hole cut by a boring bar does not end up the same size as the boring bar. The size depends on the degree to which the cutting edge is off-center. I think the chatter you experience may stem from this problem. Basically, the cutting edge ...
- Tue Jan 18, 2022 7:31 pm
- Forum: Flute Forum
- Topic: reaming
- Replies: 30
- Views: 5568
reaming
... The reamer vibrates, and this causes things to loosen. If I crank down hard enough on the wood in the lathe chuck, it's fine. I've put some ... one homemade and two commercially made. The 3/4 round one I made didn't chatter the way the commercial ones do, but it sure seized a lot. This only ...
- Mon Oct 11, 2021 4:38 am
- Forum: The Chiff and Fipple Whistle Forum
- Topic: MK Midgie High D
- Replies: 2
- Views: 2543
MK Midgie High D
Anyone curious about this one? They are taking pre orders and won't be shipping for 2 or three months, but I was a little surprised to find no chatter about it here. I wonder if there aren't a couple of prototypes in circulation... https://mkwhistles.com/products/mk-midgie-high-d?variant=40537802539193
- Mon Jun 21, 2021 4:47 pm
- Forum: The Chiff and Fipple Whistle Forum
- Topic: Drill Press or Milling Machine?
- Replies: 2
- Views: 2152
Re: Drill Press or Milling Machine?
... especially in Aluminium, it produces a clean sided cut without the chatter you get from drilling. Using a mill also lets you do all the different size holes without changing bits.
- Sat Nov 28, 2020 10:40 am
- Forum: The Chiff and Fipple Whistle Forum
- Topic: Tunes for Animals
- Replies: 18
- Views: 6360
Tunes for Animals
I have a cat and two dogs, so far, the cat has absolutely no interest in ... or do with the whistle. One dog will regularly howl if I play the old USSR National Anthem or police ... lot of tunes, but over in another thread, there's chatter about playing for seagulls, and horses, and ...